|
1、Brief introduction
of products :
This product is a kind of special
rubber that can be sulphurated under the
room temperature. Its chemical compositions
are with gathering two methyl silicons
oxygen and alkane of the hydroxyl, the
chemical structural formula is:
CH3
┌─ CH3 ─┐ CH3
│ │
│ │ │
HO ─ Si ─ O ┼── Si
── O ┼─ Si ─ OH
│ │
│ │ │
CH3 └─ CH3
─┘n CH3
n=450-850 |
2、Quality index
:(HG2-1494-83):
|
Project
|
Index
|
|
#106
|
#107A
|
#107B
|
|
Appearance
|
White one flow the lotion form
thing
|
Flow colourlessly and
transparently colloidally
|
Flow colourlessly and
transparently colloidally
|
|
Viscidity (25℃)cs
|
≤200000
|
2000-7000
|
7000-12000
|
|
Volatilize the share for (3
hours /150℃)
|
≤3%
|
≤2%
|
≤2%
|
|
The surface sulphurates time
hour
|
-
|
≤2
|
≤2
|
3、Performance and use
Product this have lying between electric
performance fine after sulphurating,
insulating able to bear electric arc corona
, able to bear oxygen and able to bear
atmosphere wear out excellentlying,
chemistry is steady. Can be - using in 60 -
+180 degrees Centigrade of temperature
ranges. It is convenient and operating
simple and easily that the room temperature
sulphurates one of the characteristics of
the silicon and lies in shaping. So, this
product can be used in the insulation of
such electronic elements as radio , electron
tube instrument , semiconductor ,etc. and
association one , take precautions against
earthquakes , sealing dampproofly
extensively. Can make die material and mould
material applied to resin solidification
shaping .
4、Operation method
(room temperature sulphurates the craft ) :
Fetch 0 for 100 pieces of glue and
catalyst (two cube base tin of silicic acid
of daily February ) before using. 5-5
copy,it pay pharmaceutical I (daily for
second silicic acid ester not straight,) mix
and not even 1-10 copy fully,namely suitable
for by flooding, casting or applying paint
with a brush not spending. Pass the
preliminary solidification of 2-4 hour , the
basic stability after 3 days. Explanation 、:
l、Catalyst , pay consumption , I of
pharmaceutical, to sulphurate glue to be
performance influence big, but to sulphurate
speed of course have obvious function .
Consumption its heavy to sulphurate speed to
be fast.
2、Put catalyst into and pay sizing
material , I of pharmaceutical , under the
general room temperature , should use up
within 1-2 hours . So need it according to
consumption , use and mix at the same time
at the same time.
3、The work piece surface that is exposed
to with the sizing material must be through
purification (wipe clean with the acetone or
the benzene, it is and then it dry,)
otherwise can't influence there aren't glue
and work piece ,scribble not lasting
pharmaceutical surface in case of necessity
(for instance: Methyl three acetyl oxygen
there is on two chlorine methane for
solution 10% in silane base ,) with
increasing not for intensity of forminging.
4、If find while mixing and compounding
the sizing material that there are bubbles
that are sneaked into, release the vacuum to
get rid of; It find it take place for a long
time surface glue (the too the following to
sulphurate ,),the getting getting getting
more straight a more bit more more slightly
second silicic acid ester can have overcome
when not compounding ; Find the deep
department difficult to sulphurate after the
strong encapsulation, even does not
sulphurate for a long time, can be while
compounding, join 0 of every 100 copies of
sizing material . Water of 4 can be solved.
5、Is it pay I straight silicic acid
second very easy to become damp and rotten
ester that pharmaceutical spend to make ,
should be airtight to store, if give play
to, namely unsuitable to use. Two cube base
tin of silicic acid will condense when the
temperature is lower in February when use as
catalyst , with before must have water bath
it is warm the hot to dissolve.
6、The room temperature of different
types sulphurates the silicon rubber and can
try one's utmost and mix each other in
wanton proportion , performance of the
material by regulating construction
viscidity and combing taking.
5、 Packaging and
storing and transport :
1, This product with clean , antirusting
the container splendid attire dry. Packing
instructions is sealed and does not leak .
(pack the size and can be made according to
the need of user).
2, This product should be put in the
shady and cool dry place in storing ,
transportation, prevent being exposed to the
sun and rain.
3, It was three years since this
product stored one effectively. |